FAGOR
FAGOR
Sort by
Show result
  • Well filled with water through a solenoid value which is operated by a switch on the front of the machine. The filling pipe is located at the back of the machine.
  • Double-walled lid with a draining rack at the back to redirect condensation water towards the well interior.
  • The closed lid is the same height as surface tops of the range and since it does not have any protruding element or reinforcement, it can be used as a worktop.
  • Compensation system to prevent sharp falls.
  • Front access lid handle.
  • Electrically heated using stainless steel heating elements located below the base of the well.
  • Thermostatic temperature control of the well floor, between 50°C and 300°C.
RM0.00
  • Well filled with water through a solenoid value which is operated by a switch on the front of the machine. The filling pipe is located at the back of the machine.
  • Double-walled lid with a draining rack at the back to redirect condensation water towards the well interior.
  • The closed lid is the same height as surface tops of the range and since it does not have any protruding element or reinforcement, it can be used as a worktop.
  • Compensation system to prevent sharp falls.
  • Front access lid handle.
  • Gas heating with high-efficiency stainless steel burners made of four tubes which are activated and controlled by a safety valve with a thermocouple.
  • Thermostatic temperature control of the well floor, between 50°C and 300°C.
RM0.00
  • Thermostatic temperature control of the water, between 30°C and 90°C.
  • Controls with a protective support base and system to prevent water infiltration (IPX5 protection).
  • AISI 304 stainless steel heating elements located outside the well.
  • Safety thermostat.
  • 2 crossbars to support Gastronorm containers.
  • Containers not included.
RM0.00
  • Thermostatic temperature control of the water, between 30°C and 90°C.
  • Controls with a protective support base and system to prevent water infiltration (IPX5 protection).
  • AISI 304 stainless steel heating elements located outside the well.
  • Safety thermostat.
  • 2 crossbars to support Gastronorm containers.
  • Containers not included.
RM0.00
  • 397 x 580 mm double grates (397 x 290 mm for each burner) enabling the use of large pots and pans. The reduced distance of 75 mm between the central bars makes it possible to use pots with a very small diameter (8 cm), avoiding the risk of smaller pans tipping over.
  • The grates are made of RAAF enamelled cast iron (resistant to alkaline and acid products, fire and high temperatures).
  • Double-crown burners and diffusers made of nickel-plated cast iron which guarantee an even distribution of heat from the flame to the base of the pans, even for large pans. This therefore prevents heat from building up in a specific point and optimises energy transfer to the product.
  • Low-consumption pilot light and thermocouple located within the body of the burner for greater protection.
  • Flexible stainless-steel gas pipes, facilitating internal manipulations in order to make repairs easier.
  • system to prevent water infiltration.
  • High-temperature enamelled cast iron flue protector which is flush with the grates therefore improving manoeuvrability, supporting larger containers and increasing the usable surface area.
  • Access to components from the front.
RM0.00
  • 397 x 580 mm double grates (397 x 290 mm for each burner) enabling the use of large pots and pans. The reduced distance of 75 mm between the central bars makes it possible to use pots with a very small diameter (8 cm), avoiding the risk of smaller pans tipping over.
  • The grates are made of RAAF enamelled cast iron (resistant to alkaline and acid products, fire and high temperatures).
  • Double-crown burners and diffusers made of nickel-plated cast iron which guarantee an even distribution of heat from the flame to the base of the pans, even for large pans. This therefore prevents heat from building up in a specific point and optimises energy transfer to the product.
  • Low-consumption pilot light and thermocouple located within the body of the burner for greater protection.
  • Flexible stainless-steel gas pipes, facilitating internal manipulations in order to make repairs easier.
  • system to prevent water infiltration.
  • High-temperature enamelled cast iron flue protector which is flush with the grates therefore improving manoeuvrability, supporting larger containers and increasing the usable surface area.
  • Access to components from the front.
RM0.00
  • 397 x 580 mm double grates (397 x 290 mm for each burner) enabling the use of large pots and pans. The reduced distance of 75 mm between the central bars makes it possible to use pots with a very small diameter (8 cm), avoiding the risk of smaller pans tipping over.
  • The grates are made of RAAF enamelled cast iron (resistant to alkaline and acid products, fire and high temperatures).
  • Double-crown burners and diffusers made of nickel-plated cast iron which guarantee an even distribution of heat from the flame to the base of the pans, even for large pans. This therefore prevents heat from building up in a specific point and optimises energy transfer to the product.
  • Low-consumption pilot light and thermocouple located within the body of the burner for greater protection.
  • Flexible stainless-steel gas pipes, facilitating internal manipulations in order to make repairs easier.
  • system to prevent water infiltration.
  • High-temperature enamelled cast iron flue protector which is flush with the grates therefore improving manoeuvrability, supporting larger containers and increasing the usable surface area.
  • Access to components from the front.
RM0.00
  • Laser-cut joints, automatic welding and polished. - Motorised or crank operated elevation systems which raises the pan until it is vertical, to empty it completely.
  • Versions with cast iron and stainless steel pans.
  • Pan design with a rounded corners and no edges, and with a wide opening for unloading, making all cooking and cleaning operations easier.
  • Flange around the perimeter to stop any condensed water from spilling over.
  • The bottom of the wells is very thick (8 mm for iron pans and 10 mm for stainless steel pans), guaranteeing even heat distribution.
  • Pans filled with water by means of electric valve operated with switch on the front of the machine. The filling pipe is located at the back of the machine.
  • Double walled lid with drainer at the back to redirect water of condensation back into the well.
  • Lid balance system by springs. Compensation system to avoid heavy falls. Can be regulated, with the same system for all modules.
  • Micro breaking switch halts heating when the pan is raised.
  • High temperature enamelled cast iron flue protector.
  • Access to the components from the front.
  • Machines with IPX5 grade water protection.
  • Front access lid handle.
  • Electrically heated models use shielded stainless steel heating elements located under the bottom of the pan.
  • Temperature of the bottom of the pan controlled by thermostat, between 50 and 310 °C.
  • The heating by branched burners or electrical heating elements located in the base of the pan itself, together with the high thickness of the bottom of the pan, ensure maximum uniformity of temperature distribution in all cases, guaranteeing even cooking.
RM0.00
  • Laser-cut joints, automatic welding and polished. - Motorised or crank operated elevation systems which raises the pan until it is vertical, to empty it completely.
  • Versions with cast iron and stainless steel pans.
  • Pan design with a rounded corners and no edges, and with a wide opening for unloading, making all cooking and cleaning operations easier.
  • Flange around the perimeter to stop any condensed water from spilling over.
  • The bottom of the wells is very thick (8 mm for iron pans and 10 mm for stainless steel pans), guaranteeing even heat distribution.
  • Pans filled with water by means of electric valve operated with switch on the front of the machine. The filling pipe is located at the back of the machine.
  • Double walled lid with drainer at the back to redirect water of condensation back into the well.
  • Lid balance system by springs. Compensation system to avoid heavy falls. Can be regulated, with the same system for all modules.
  • Micro breaking switch halts heating when the pan is raised.
  • High temperature enamelled cast iron flue protector.
  • Access to the components from the front.
  • Machines with IPX5 grade water protection.
  • Front access lid handle.
  • Gas heated models use steel burners with six branches (eight in the pan with one and a half modules), operated and controlled by safety valve with thermocouple.
  • Temperature of the bottom of the pan controlled by thermostat, between 50 and 310 °C.
  • The heating by branched burners or electrical heating elements located in the base of the pan itself, together with the high thickness of the bottom of the pan, ensure maximum uniformity of temperature distribution in all cases, guaranteeing even cooking.
RM0.00
  • Surface tops manufactured in 2 mm thick AISI-304 stainless steel.
  • Laser-cut joints, automatic welding and polished.
  • Wells stamped into the surface top.
  • Cold zone in the lower part of the well, which helps to maintain the quality and characteristics of the oil in use for longer.
  • Thermostatic temperature control between 60 and 200 °C.
  • Gas models with three longitudinal heating tubes integrated into the well.
  • High efficiency gas burners.
  • Electric models with AISI-304 stainless steel heating elements located inside the well, which can be swivelled by more than 90° for perfect cleaning.
  • High-power machines which heat up very fast and with a high power:litre ratio (up to 1.00 kW/litre in gas models).
  • Ignition by spark train for the gas models.
  • Safety thermostat in all models.
  • Unloading of oil from the well by means of a robust and reliable ball valve, resistant to high temperatures.
  • With individual lids for each well.
  • High temperature enamelled cast iron flue protector.
  • Access to the components from the front.
  • Machines with IPX5 grade water protection.
RM0.00
  • Surface tops manufactured in 2 mm thick AISI-304 stainless steel.
  • Laser-cut joints, automatic welding and polished.
  • Wells stamped into the surface top.
  • Cold zone in the lower part of the well, which helps to maintain the quality and characteristics of the oil in use for longer.
  • Thermostatic temperature control between 60 and 200 °C.
  • Gas models with three longitudinal heating tubes integrated into the well.
  • High efficiency gas burners.
  • Electric models with AISI-304 stainless steel heating elements located inside the well, which can be swivelled by more than 90° for perfect cleaning.
  • High-power machines which heat up very fast and with a high power:litre ratio (up to 1.00 kW/litre in gas models).
  • Ignition by spark train for the gas models.
  • Safety thermostat in all models.
  • Unloading of oil from the well by means of a robust and reliable ball valve, resistant to high temperatures.
  • With individual lids for each well.
  • High temperature enamelled cast iron flue protector.
  • Access to the components from the front.
  • Machines with IPX5 grade water protection.
RM0.00
  • Surface tops manufactured in 2 mm thick AISI-304 stainless steel.
  • Laser-cut joints, automatic welding and polished.
  • Wells stamped into the surface top.
  • Cold zone in the lower part of the well, which helps to maintain the quality and characteristics of the oil in use for longer.
  • High-precision electronic oil temperature control between 60°C-200°C, +/- 1°C.
  • Setpoint temperature display with an indicator to show when temperature has been reached.
  • Electric models with AISI-304 stainless steel heating elements located inside the well, which can be swivelled by more than 90° for perfect cleaning.
  • Time control card per basket with audible alarm.
  • Safety thermostat in all models.
  • Unloading of oil from the well by means of a robust and reliable ball valve, resistant to high temperatures.
  • With individual lids for each well.
  • High temperature enamelled cast iron flue protector.
  • Access to the components from the front.
  • Machines with IPX5 grade water protection.
RM0.00
  • Surface tops manufactured in 2 mm thick AISI-304 stainless steel.
  • Laser-cut joints, automatic welding and polished.
  • Wells stamped into the surface top.
  • Cold zone in the lower part of the well, which helps to maintain the quality and characteristics of the oil in use for longer.
  • Thermostatic temperature control between 60 and 200 °C.
  • Gas models with three longitudinal heating tubes integrated into the well.
  • High efficiency gas burners.
  • Electric models with AISI-304 stainless steel heating elements located inside the well, which can be swivelled by more than 90° for perfect cleaning.
  • High-power machines which heat up very fast and with a high power:litre ratio (up to 1.00 kW/litre in gas models).
  • Ignition by spark train for the gas models.
  • Safety thermostat in all models.
  • Unloading of oil from the well by means of a robust and reliable ball valve, resistant to high temperatures.
  • With individual lids for each well.
  • High temperature enamelled cast iron flue protector.
  • Access to the components from the front.
  • Machines with IPX5 grade water protection.
RM0.00
  • Surface tops manufactured in 2 mm thick AISI-304 stainless steel.
  • Laser-cut joints, automatic welding and polished.
  • Wells stamped into the surface top.
  • Cold zone in the lower part of the well, which helps to maintain the quality and characteristics of the oil in use for longer.
  • Thermostatic temperature control between 60 and 200 °C.
  • Gas models with three longitudinal heating tubes integrated into the well.
  • High efficiency gas burners.
  • Electric models with AISI-304 stainless steel heating elements located inside the well, which can be swivelled by more than 90° for perfect cleaning.
  • High-power machines which heat up very fast and with a high power:litre ratio (up to 1.00 kW/litre in gas models).
  • Ignition by spark train for the gas models.
  • Safety thermostat in all models.
  • Unloading of oil from the well by means of a robust and reliable ball valve, resistant to high temperatures.
  • With individual lids for each well.
  • High temperature enamelled cast iron flue protector.
  • Access to the components from the front.
  • Machines with IPX5 grade water protection.
RM0.00
  • 2 mm stainless AISI-304 steel top with rounded edges for easy cleaning.
  • Laser cut and automatic welding for a perfect adjustment of sides between modules with square angle finish.
  • Integrated AISI-304 stainless steel well with rounded edges for easy cleaning.
  • The well can be configured to fit different Gastronorm containers of different sizes and 150 mm deep. Well dimensions: GN-[1/1+1/3].
  • Standard equipment: 3 crossbars for Gastronorm containers support.
  • The top is ready to have a water inlet installed to fill the well.
  • The well can be easily emptied by extracting the overflow tube.
  • AISI 304 stainless steel resistances outside the well.
  • Range of temperature between 30 and 90 °C controlled by thermostat.
  • Safety thermostat.
  • Water-tight and protecting-support controls.
  • High temperature protector for the chimney made of enamelled cast iron.
  • Front access to components.
RM0.00